Basic PDU

28-Outlet IEC C13/C19 Vertical Rack PDU, 110–250 V 63 A, Hydraulic Breaker and SPD, 0U

Quick Answer28-Outlet IEC C13/C19 Vertical Rack PDU, ⁦110–250⁩ V 63 A, Hydraulic Breaker and SPD, 0U — an IDCPDU Basic PDU for data-centre and equipment-room racks.

Surge clamped before the power supplies — Lightning and switching surges are discharged at the strip; the status lamp shows when the cartridge is spent instead of failing silently.
28 outlets on one strip — A single strip feeds a whole rack, so adding a node no longer means a second PDU and a second feed cable.
0U vertical — no rack units consumed — The strip hangs on the rear post, so every U stays available for servers.
⁦110–250⁩ V wide input — One build covers 120 V and 230 V sites and rides out a brownout instead of dropping the load.
C13 and C19 side by side — Servers, switches and storage hang off one strip — no second PDU just because the C19 count did not match the drawing.
Breaker ahead of the outlets — A fault trips inside the strip, not at the upstream panel — the rest of the row keeps serving traffic.

Tel: +86-574-63783045 · ricky@idcpdu.com

28 IEC C13/C19 outlets on a 0U strip
One PDU serves a fully populated 42U rack
Hydraulic breaker plus 1-lamp surge protection
Twenty-eight outlets let a single strip feed both sides of a dense rack through C13 cords with C19 for the heavier appliances, so the second PDU can be reserved as an A/B feed.
The 1358 mm body is 60 × 85 mm and mounts on the rear rail without blocking the door or the vertical cable manager; the breaker doubles as a local isolator.
Used in dense compute racks, virtualisation clusters and storage arrays where outlet count, not switching, is the constraint.
Outlet mix and cable length are built to drawing: layout within 30 minutes, quotation within 1 hour.

Frequently Asked Questions

Can 28 outlets run on one 63 A feed?

Yes, if total load stays under 63 A. With ⁦1–2⁩ A servers, 28 outlets typically draw ⁦30–45⁩ A, leaving margin for peak draw.

Should I still install a second PDU for redundancy?

For A/B power you need two feeds and two strips; this PDU covers one feed, so a second unit on the other feed gives full redundancy.

What is the C13 to C19 split?

It is set at order; a typical dense rack uses 22 C13 and 6 C19. Any ratio can be built on the same body.

Is the SPD monitored remotely?

No — it has a local indicator lamp. Remote alarm requires the metered network version.

Does the strip fit a 47U rack?

The standard body is 1358 mm for 42U; a longer body is cut for 47U on request.

What is the production time?

Drawing within 30 minutes, quotation within 1 hour, production ⁦7–15⁩ working days after approval.

Rack standard	19-inch EIA-310
Installation	Vertical (0U)
Mounting length	1358 mm
Body dimensions (W×H)	60 × 85 mm
Outlet configuration	28× IEC C13 / C19
Outlet rating	C13: 10 A; C19: 16 A
Max input current	63 A
Input voltage	⁦110–250⁩ V AC, 50/60 Hz
Phase	Single-phase
Input connection	OT terminal junction box
Main breaker	Hydraulic magnetic breaker
Surge protection	1-lamp SPD
Housing	Cold-rolled steel, black powder coat
Operating temperature	⁦10–45⁩ °C
Relative humidity	⁦0–90⁩% RH, non-condensing
Included accessories	M6×16 screws, user manual
Certification	CE / EMC; built under ISO 9001

28-Outlet IEC C13/C19 Vertical Rack PDU, 110–250 V 63 A, Hydraulic Breaker and SPD, 0U

Product Description

Product Specifications

Product documents

Support & Contact

Feedback

Frequently Asked Questions

Related Products

14-Outlet Swiss SEV 1011 Vertical Rack PDU, 220 V, 10 A per Outlet, 0U

16-Outlet GB Socket Vertical Rack PDU, 220–250 V 63 A, Main and Branch Breakers, 0U

18-Outlet South African Socket Vertical Rack PDU, 250 V 63 A, Hydraulic Breaker and SPD, 0U

19-Outlet British BS 1363 Vertical Rack PDU, 230 V 63 A, Hydraulic Breaker, 0U